nts350 series 350 watts total power: 200 - 350 watts input voltage: 85 - 264 vac 120 - 300 vdc # of outputs: single special features ? active power factor correction ? iec en6100-3-2 compliance ? remote sense ? power fail and remote inhibit ? single wire current sharing ? built-in emi flter ? low output ripple ? 5 v standby ? 12 v fan output ? overvoltage protection ? overload protection ? thermal overload protection ? dc power good ? built in or-ing diode/fet ? optional fan cover (-cf suffx) ? optional end fan cover (-cef suffx) safety ? tuv 60950 ? ul 0950 ? csa 60950 ? culus 60950 (-cef) ? nemko 60950 ? austel 60950 ? cb certifcate and report ? ce mark (lvd) ? ccc certifcate electrical specifcations input input ra nge: 85 - 264 vac (wide range) frequency: 47 - 440 hz (47- 63 hz for -cef versions) inrush current: 38 a max., cold start @ 25 c effciency: 85% typical at full load emi flter: fcc class b conducted and radiated; cispr22 class b conducted and radiated; en55022 class b conducted and radiated; vde0878pt3 class b conducted and radiated. safety ground leakage current: < 0.5 ma @ 50/60 hz, 264 vac input output maximum power: 200 w for convection; 350 w with 30cfm forced air adjustment range: 5% standby output: 5 v @ 2 a regulated, 5% fan output: 12 v @ 1 a, -5 %, +7%, 0.5 a for -cf version hold-up time: 20 ms @ 350 w load, 115 vac nominal line at factory voltage setting overload protection: short circuit protection on all outputs. case overload protected @ 115 - 130% of peak rating overvoltage protection: 20 - 35% above nominal output data sheet power
nts350 series data sheet logic control power failure ttl logic signal goes high 100 - 500 msec after main output. it goes low at least 4 msec before loss of regulation remote on/off requires an external contact closure to inhibit outputs dc ok ttl logic goes high after the output is in regulation. it goes low when there is loss of regulation. remote sense compensates for 0.5 v lead drop min. will operate without remote sense connected. reverse connection protected. ordering information model number output voltage minimum load maximum load with convection cooling maximum load with 30cfm forced air peak load 1 regulation 2 ripple p/p (pard) 3 nts353 12 v 0 a 16.6 a 29.2 a 33 a 2% 120 mv NTS355 24 v 0 a 8.3 a 14.6 a 16.5 a 2% 240 mv nts358 48 v 0 a 4.2 a 7.3 a 8.2 a 2% 480 mv nts359 54 v 0 a 3.7 a 6.5 a 7.4 a 2% 540 mv 1. peak current lasting < 30 seconds with a maximum 10% duty cycle. 2 . at 25 c including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . peak-to-peak with 20 mhz bandwidth and 10 f (tantalum capacitor) in parallel with a 0.1 f capacitor at rated line voltage and load ranges. 4 . cf suffx added to the model number indicates cover with top fan. -cef suffx added to the model number indicates cover with end mounted fan cover and ac inlet 5. this product is a component power supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. emc compliance to appropriate standards must be verifed at the system level. this product is for sale to oems and system integrators, including through distribution channels. it is not intended for sale to end users. environmental specifcations operating temperature: 0 to 50 c ambient derate each output as 2.5% per degree from 50 to 70 c. storage temperature: -40 c to +85 c electromagnetic susceptibility: designed to meet en61000-4; -2, -3, -4, -5, -6, -8, -11 level 3 humidity: operating; non-condensing 10% to 90% rh vibration: three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances. 2 g peak 8 hz to 500 hz, operational mtbf demonstrated: 1m hours at full load and 25 c ambient conditions lps100-m series data sheet
nts350 series data sheet pin assignments connector sk1 pin 1 line pin 3 neutral pin 5 ground sk5 pin 1 v1 swp pin 2 - remote sense pin 3 + remote sense pin 4 5vsb (standby) pin 5 5vsb return pin 6 +12v pin 7 common pin 8 inhibit pin 9 dc power good (dc ok) pin 10 power fail (pok) adjustment potentiometers p1 +v1 output adjust p3 +5vsb adjust mating connectors sk1 ac input molex 09-50-8051 (usa) molex 09-91-0500 (uk) pins:08-52-0113 sk2,3,4 molex bb-124-08 sk5 control signals molex 90142-0010 pins: 90119-2110 or amp: 87977-3 pins: 87309-8 artesyn embedded technologies connector kit #70-841-022 includes all of the above 1. specifcations subject to change without 2. all dimensions in inches (mm), tolerance is 0.2. 3.specifcations are at factory settings 4. mounting maximum insertion depth is 0.12. 5.warranty: 2 year 6.weight: nts35x 1.65 lbs/750g. nts35x-cf 2 lbs/909g. nts35x-cef 2.25 lbs/1022g. 1 5 61 0 lps100-m series data sheet
worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 nts350 series data sheet nts350 ds 21mar2016 a b a b a b a b a b a b a b a b 9.15" (232.3) air flow direction 4.0" (101.6) 1.61" (40.9) 1.255" (31.9) 0.862" (21.9) 2.40" (61) 6.244" (158.6) 5.85" (148.6) 0.862" (21.9) 6.437" (63.5) 0.752" (19.1) 2.9" (73.6) 4.7" (119.6) 5.5" (139.7) m3 (8 places) #6-32 (8 places) mechanical drawing - cef option for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2016 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com
nts350 series data sheet mechanical drawing 4.0 (101.6) 7.0 (177.8) (2x) 4.7 (1 19.6) 1.5 (38.10) (2x) 6.4 (3x) .75 (19.1) 1.14 (29.1) (4x) 2.5 (63.5) (2x) 5.5 (139.7) 5.85 (148.7) 6.25 (158.7) (see note 5) -cf option sk1 531 + v or-ing out -cf option + v out common p1 p3 p1 p3 #6-32 (8 places) m3 (8 places) a a a a b b bb a b a b 1.27 (32.26) (must be used in parallel operation) (do not use in parallel operation) 1 5 6 10 p1 voltage adj po t
|
